Category: battery recondition laptop

How To Restore A Car Battery | Eastwood Blog

If you have an old car battery that has a low voltage output, it might be time to start considering a small restoration project. Reviving worn out car batteries is an important money and time saver and one that could save you from hardships in the future. Below, we take a look at how to best restore your car battery and why it is so important.

Car batteries are types of lead-acid batteries, meaning that they have lead-acid cores that can suffer a condition called sulfation over time. Sulfation occurs when sulfur accrues on the lead plates that reside inside the battery casing. If there isn’t an over-abundance of sulfur corrosion, a car battery can be restored, which is much preferred to replacing a costly battery. In order to determine whether or not you should restore your battery, consider the following details:

With these factors in mind, it is time to gather your materials and restore your car battery.

You will need the following items to perform your battery restoration project: baking soda, distilled water, a power drill, magnesium sulfate (commonly known as Epsom salt), non-metallic storage funnel, non-metallic storage container, plastic replacement plugs, safety glasses, a three-phase battery charger for lead-acid batteries, water, work gloves, and a wrench. The first thing to do is turn your car off, and let your car battery cool for about an hour. Once the battery is cool, open the car hood and use your wrench to detach the negative battery cable first and then the positive cable. Be sure not to touch your wrench to any other metal part of the car to avoid experiencing a small jolt of electricity. Now, carefully remove the battery from the car.

Take off the plastic cell caps on the topside of the battery, and find the location of the sealed cells inside the casing indicated by small marks. Put on your safety glasses, and drill into the sealed cells using your power drill. Put your work gloves on, and turn the battery upside down above a non-metallic storage container to drain the fluid inside. Add baking soda to the battery fluid in slowly paced increments of tablespoons to neutralize it. Once the fluid stops bubbling, close the container tightly, and take it to a hazardous waste disposal site. Now, take your Epsom salt and stir one part of it into three parts warm, distilled water until you have one full quart of magnesium sulfate solution. Insert your non-metallic funnel into one of the now open battery cells, and carefully pour some of your magnesium sulfate solution into the battery. Lightly shake the battery to evenly distribute the solution inside, and let the solution sit. Repeat this step for the other cells as well.

Make sure your three-phase battery charger is off before you clip the positive lead onto the positive battery terminal and the negative lead onto the negative battery terminal. Set the charger’s dial to 12 volts, and then turn on the charger. Leave the trickle charge going for at least 12 full hours before turning it off and unclipping the leads from the battery terminals. After this is done, return the caps onto their cells, or use your plastic plugs to cover up the drilled holes, and reinsert the battery into its place underneath the car hood. Once, you have reconnected the positive cable first and then the negative cable to their terminals, you have successfully restored the battery. It is best to repeat this entire process at least once a week for one whole month in order to ensure that any remaining deposited sulfur is dissolved. This way, your battery will be healthier and last much longer.

To learn more about car batteries and for various DIY car tutorials, be sure to visit Eastwood.com .

The lead is used in soldering the components in the circuit board.

This causes the air to become polluted by toxic gases. But, Vo – IP systems provide a great way to

use more of the computer and Internet resources that are

already available instead of taking the time to create and use

more.

Louis Beaudreau, I have a question for you: You do not put acid and water back into the battery and you leave the magnesium sulfate solution in the battery?

why can’t one use new battry acid to restore a battery?

Why doesn’t anyone suggest this as an option more often?

This works…so far, it has been two weeks. Still holds charge. Done it just as it says. Just some baking soda, and epsom salt. Make sure you use distilled water.

I just did mine but put new battery acid instead of distilled water…have it hooked up to a 12 18watt solar panel for charhing..let’s see how it turns out.

if you want battery recondition laptop Download the complete guide here!