Category: recondition battery macbook air

Intelligent Automotive Battery Charger And Reconditioner

This

Intelligent Battery Reconditioner & Charger incorporates reconditioning

processes to recover deeply discharged batteries, especially found in deep

cycle batteries, by using latest Inverter technology (high frequency

switching circuitry which converts incoming AC input into 12v/24v DC

outputs). Its built-in microprocessor control constantly senses the

condition of the battery during the whole charging process, and provides the

accurate Amperage and Voltage to the battery based on the 7 designated charging

stage requirements. If it finds that the battery has failed after the

conducted battery test, it will immediately start the

reconditioning process where it introduces low constant current at higher

voltage to recondition the battery for 4 hours before it begins another test.

Main Features:

 –    Microprocessor controlled charging that always monitors the battery

condition during operation to determine the correct action that should

be taken.

 –    Very Accurate

in determining the correct amount of current and voltage during charging which never

overcharges a battery.

 –   Its

Desulphation process helps to break down sulphate that occurs in battery

which has been left flat for extended periods of time or when lead sulphate

hardens and clog up the battery cells. This helps to restore lightly

sulphated batteries back to its best state, thus increasing performance and

prolonged battery life.

 –    Automatic 7 stage switching mode

makes charging much easier, quicker and safer on all types of lead acid batteries with

no worries of disconnecting the battery after full charge.

Constant current bulk charge and 7 stage intelligent charging provides the

fastest possible way to recharge the battery without overcharging it

eliminating any possible damage.

Step1:

Desulphation –

(Pulse Charge) This process breaks down sulphation that occurs in batteries left flat for

long periods, returning them back to

life.

Step 2:

Soft-start – (Half Current) Preliminary charge process that gently introduces

power to the battery , thus protecting the battery and increasing its life.

Step 3:

Bulk

Charge – (Max Current) Maximum rate charge which puts a large amount of power

into the battery in a shortest possible time. 80% charge state.

Step 4:

Absorption – (Constant Voltage) Slower charge rate so the battery

can absorb more power and reach 100% charge level without overcharging.

Step 5: Battery Test –

(Voltage Monitor) 90

seconds Automatic Battery Test to confirm successful state of charge and

determine further course of action.

Step 6:

Recondition – (Constant Current) Recovers deeply discharged batteries, Equalizes the

cells charge levels across the battery, Equalizes the acid content between top and bottom of

the cells.

Step 7:

Maintenance Float Charge – (Float Pulse) Maintains the battery at 100%

state of charge without damage or overcharging.

  – 

Self-Test on Power-On, ensures internal circuitry reliability before

charging commence.

  –   Battery Reverse Polarity and Output

Short Circuit: spark-less protection.

  –  No-Battery Connection Protection: The charger can not

be used as a stand alone power supply.

  –   Highly

efficient: Produces much less heat during charging due to less energy loss.

  –   Light in

weight and compact in size compared with traditional chargers. Average weight

– 1kg.

  –   Temperature controlled internal cooling fan,

Thermal Protection @ 65degC .

  –  Over-voltage

protection, Faulty Battery protection,

Audible Alarms.

  –   Easy-View Charging

process indication by flashing Color LEDs.

  –  Low Priced comparing to

alternative units even for DIY / private applications.

  –  Truly, connect-and-forget, trouble free battery maintenance.

  –  Suitable for most Lead Acid Batteries , sealed

or not, including Calcium, GEL and AGM.

 – The

Charger can be left connected infinitely without harming the battery

which helps to maintain the battery charge levels – incorporating Float

Charge processes (Pulse charging). If the battery terminal voltage goes

below a lower limit, the charger automatically goes back to the beginning of

the charging curve. However, being an Intelligent Charger, it

determines which step to begin with depending on the state of the battery.

It might not necessarily begin from Step-1 every time.

This is also a great future for battery back-up installations as the charger

will take care of the battery’s needs immediately after the main power has

come back. Batteries love recharging as soon as possible after hard work.

 – This is NOT a Fast Charger for Jump

Starting your vehicle!

Battery

Conditioner and Charger – Manual  (PDF file) Get to know your

charger!

Have you batteries properly maintained, always 100% charged

and ready for work.

More information about Batteries can be found in our

Tech Things to Know

section.

Available in 12v and 24v versions

 

12V / 5A   up to 100AH batteries

12V / 7A   up to 140AH batteries

 

12V / 10A   up to 200AH batteries

 

12V / 15A   up to 300AH batteries

 

12V / 20A   up to 400AH batteries

Also in:  24V / 5A and 24V / 10A

Many applications include: Automotive, telecoms, standby generators,

recreation, marine, aviation, emergency vehicles on stand by and many other

industries where reliably charged batteries are vital.

This intelligent charger is also indispensable for doing extensive

diagnostics or electrical work on vehicles. No more worries about lost radio

codes, reset ECU’s or flat batteries just before the customer arrives.

Automotive Equipment –

in tune with the Future

if you want recondition battery macbook air Download the complete guide here!